PCE Instruments PCE-PHC 10 Manual
PCE Instruments
Measuring equipment
PCE-PHC 10
Read below 📖 the manual in Italian for PCE Instruments PCE-PHC 10 (22 pages) in the Measuring equipment category. This guide has been helpful for 5 people and has been rated 4.5 stars on average by 2 users
Page 1/22
pH
CONTROLLER/MONITOR
PCE-PHC 10
Your
MON
precision measurement. Although this pH controller is a
complex and delicate instrument, its durable structure
developed. Please read the following instructions carefully
and always keep this manual within easy reach.
OPERATION MANUAL
Caution Symbol
Caution :
* Risk of electric shock !
Caution :
* Do not use fingers or any tool
to touch the Wire Terminals.
* Do not apply the relay contact load
current > 0.5 Amp.
* The instrument contains no user
serviceable parts and should not
be opened by the user.
* Repair or after service should be
done by a qualified technician only.
* Power supply should apply the
correct ACV power voltage
* Cleaning - Only use the dry cloth to
clean the plastic case !
* Equipment protectted throughout
by Double Insulation or Reinforced
Insulation.
Environmental Condition
* Comply with EN61010.
Transient overvoltage at Mains Supply 2500V.
* Pollution Degree 2.
* Altitude up to 2000 meters.
* Indoor use.
* Relative humidity 80% max.
TABLE OF CONTENTS
1.
FEATURES.................................................................................................
1
2.
SPECIFICATIONS......................................................................................
2
2-1 General Specifications..........................................................................
2
2-2 Electrical Specifications........................................................................
4
3.
FRONT PANEL DESCRIPTION.................................................................
5
3-1 Display..................................................................................................
5
3-2 PV ( process value ) indicator...............................................................
5
3-3 SV ( set value ) indicator.......................................................................
5
3-4 Set Button.............................................................................................
5
3-5
â–¼
Button...............................................................................................
5
3-6
â–²
Button...............................................................................................
5
3-7 PH/Temp Button...................................................................................
5
3-8 pH control relay indicator......................................................................
5
3-9 Temp. control relay indicator................................................................
5
3-10 pH indicator.........................................................................................
5
3-11 Temp. indicator...................................................................................
5
3-12 Wire terminals ....................................................................................
5
3-13 RS232 terminal...................................................................................
5
3-14 BNC Input socket ...............................................................................
5
3-15 Case holder .......................................................................................
5
3-16 pH Electrode plug ( optional ).............................................................
5
3-17 pH Electrode ( optional ).....................................................................
5
3-18 Temp. Probe ( optional ).....................................................................
5
3-19 Temp. Wires ( optional ).....................................................................
5
4.
MEASURING PROCEDURE......................................................................
5
4-1 Terminal connection.............................................................................
6
4-2 pH calibration .......................................................................................
6
4-3 pH measurement ( with ATC probe )....................................................
7
4-4 pH measurement ( without ATC probe )...............................................
7
4-5 1st layer setting procedures..................................................................
8
4-6 2nd layer setting procedures................................................................
10
5.
pH CALIBRATION PROCEDURES............................................................
14
6. RS232 PC SERIAL INTERFACE................................................................
17
7. pH ELECTRODE QUALITY CHECK...........................................................
19
8. SYSTEM RESET.........................................................................................
19
Product Specifications
| Brand: | PCE Instruments |
| Category: | Measuring equipment |
| Model: | PCE-PHC 10 |
Do you need help?
If you need help with PCE Instruments PCE-PHC 10, ask a question below and other users will answer you
Measuring equipment PCE Instruments User Manuals
24 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
Measuring equipment User Manuals
- Measuring equipment EBERLE
- Measuring equipment Hazet
- Measuring equipment Fluke
- Measuring equipment Megger
- Measuring equipment Kogan
- Measuring equipment AkYtec
- Measuring equipment Voltcraft
- Measuring equipment Klein Tools
- Measuring equipment PeakTech
- Measuring equipment Clean Air Optima
- Measuring equipment Flex
- Measuring equipment CSL
- Measuring equipment Elgato
- Measuring equipment Kern
- Measuring equipment Be Cool
- Measuring equipment ORNO
- Measuring equipment Einhell
- Measuring equipment Mitsubishi
- Measuring equipment Noyafa
- Measuring equipment Megasat
- Measuring equipment Reely
- Measuring equipment Joy-it
- Measuring equipment Logilink
- Measuring equipment Basetech
- Measuring equipment Gossen Metrawatt
- Measuring equipment TFA
- Measuring equipment Owon
- Measuring equipment Extech
- Measuring equipment Milesight
- Measuring equipment Sonel
- Measuring equipment Flir
- Measuring equipment Testo
- Measuring equipment MSW
- Measuring equipment Stamos
- Measuring equipment Ideal
- Measuring equipment Hikmicro
- Measuring equipment Siglent
- Measuring equipment Kopp
- Measuring equipment PICO
- Measuring equipment Enda
- Measuring equipment Wachendorff
- Measuring equipment Ermenrich
- Measuring equipment Beha-Amprobe
- Measuring equipment Adwa
- Measuring equipment Tempo
- Measuring equipment Vemer
- Measuring equipment Testboy
- Measuring equipment Duro Pro
- Measuring equipment Kyoritsu
- Measuring equipment Benning
- Measuring equipment MASIMO
- Measuring equipment Stahlwille
- Measuring equipment SHX
Latest Measuring equipment User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024