PCE Instruments PCE-DPD-F2 Manual
PCE Instruments
Measuring equipment
PCE-DPD-F2
Read below 📖 the manual in Italian for PCE Instruments PCE-DPD-F2 (32 pages) in the Measuring equipment category. This guide has been helpful for 5 people and has been rated 4.5 stars on average by 2 users
Page 1/32
PCE-DPD-F1
PCE-DPD-F2
Panel meter for load cells
Digital panel meter for load cells. Provides excitaon voltage to power up to 8 cells. Standard
96 x 48 mm size (1/8 DIN). Reading with 6 digit display. Accepts 4 and 6 wire load cells, includes ‘sense’
funcon, fast access to alarm setpoints, tare and ‘auto-tare’ funcons, ‘on power up’ funcons, stabil-
ity alarms, congurable operator menu, congurable led brightness. Universal AC and DC power. Up
to 3 oponal modules for output and control (relays, transistor, control SSR, analog outputs, Modbus
RTU communicaons, RS-485 ASCII, RS-232, ...)
www.pce-instruments.com
DIGITAL PANEL METERS
4784r03
User’s Manual
2
1. Panel meter PCE-DPD-F1 & F2
Panel meter for load cells, size 96 x 48 mm (1/8 DIN)     
Digital panel meter, with 96 x 48 mm (1/8 DIN) size and 6
digits with 14 mm digit height, for load cell signals. Pro-
vides excitaon voltage congurable to +5 Vdc or +10 Vdc
to power up to 8 standard 350 Ohms cells. Scalable read-
ing from 999999 to -199999 with congurable decimal
point.
Tare funcon, with congurable controls, and ‘auto-tare’
funcon for automac tare correcon when weight is re-
moved from the cell. Three working modes with dierent
acquision speeds and noise rejecon to 50 and 60 Hz.
Output and control opons with 1, 2 and 3 relays, isolated
analog outputs, Modbus RTU communicaons, transistor
outputs, SSR control outputs, RS-485 ASCII and RS-232.
Independent alarms congurable as maximum or mini-
mum, with acvaon at setpoint or when reading is
stable, with 1 or 2 setpoints per alarm, hysteresis, inde-
pendent acvaon and deacvaon delays, congurable
inverted acvaon of the relay and congurable locked
alarms (see secon 1.13.8).
Front protecon IP65. Connecons by plug-in screw ter-
minals. For industrial applicaons.
Funcons included :
•
tare accessible from frontal key or rear contact
(see sec-
on 1.11)
• automac ‘auto-tare’ funcon (see secon 1.13.4)
• access to gross weight value and tare value (see sec-
on 1.9.5)
• funcon ‘On Power Up’ for automac acvaon of
funcons at start-up (see secon 1.13.14)
• scale factor for easy modicaon of reading units (see
secon 1.13.5)
• ‘stock units’ funcon to count units (see secon 1.13.6)
• access to the measured signal value (in mV), excitaon
current provided (in mA) and real excitaon voltage (see
secon 1.13.13)
• congurable ‘Fast access’ menu (key ‘UP’ ( )) with 5
access to selected funcons (see secon 1.13.13)
Mulple display lters, memory for maximum and mini-
mum, password, 5 congurable brightness levels.
1. Power and signal connecons
- connect the power (see secon 1.8)
- connect the signal (see secon 1.8)
- read recommendaons to connect the ‘sense’ (see secon
1.8.1) and for load cell ground connecons (see secon
1.8.2)
2. Inial setup (see secon 1.13.2)
- theorecal conguraon of the cell (obtain the load cell
data : sensivity, load and excitaon) and congure the
instrument
- apply the empirical conguraon of the cell (apply the
high and low ‘eld correcon’)
- assign the ‘system zero’
3. Advanced conguraon (oponal) (see secon 1.13.7)
- tare conguraon, see secons 1.11 and 1.13.4
1.1 How to use this manual
- funcon ‘stock units’ (see secon 1.13.6)
- scale factor (see secon 1.13.5)
- acquision modes (see secon 1.9.1)
4. Congure the alarms (oponal) (see secon 1.13.8)
5. Display lters (oponal) (see secon 1.13.10)
6. Congure operator controls (oponal)
- congure the rear control (see secon 1.13.11)
- congure the front key ‘LE’ (3)(see secon 1.13.12)
- congure the fast access (key ‘UP’ ( ))
5(see secon 1.13.13)
7. Congure other funcons (oponal)
- congure the ‘on power up’ funcon (see secon 1.13.14)
- congure the password and brightness level (see secon 1.13.17)
8. Congure the output and control opons: analog or serial
(see secon 1.13.18)
If this is the rst me you are conguring this instrument,
below are the steps to follow to install and congure the in -
strument. Read all the manual secons in order to have a
full and clear view of the characteriscs of the instrument.
Do not forget to read the installaon precauons
at secon
1.19
.
3
PCE Instruments | www.pce-instruments.com
1. Panel meter PCE-DPD-F1 & F2 2. . . . . . . . . . .
1.1 How to use this manual . . . . . . . . . . . . 2
1.2 Index . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 How to order . . . . . . . . . . . . . . . . . . 3
1.4 Material included . . . . . . . . . . . . . . . . 4
1.5 Addional informaon . . . . . . . . . . . . . 4
1.6 Front view . . . . . . . . . . . . . . . . . . . . 4
1.7 Rear view . . . . . . . . . . . . . . . . . . . . 4
1.8 Signal and power connecons . . . . . . . . . 5
1.8.1 Connecng the ‘sense’ . . . . . . . . . . . 5
1.8.2 Connecng the cell to the ground . . . . . 5
1.9 Technical specicaons. . . . . . . . . . . . . 6
1.9.1 Acquision modes. . . . . . . . . . . . . . 6
1.9.2 Signal ranges . . . . . . . . . . . . . . . . . 7
1.9.3 Number and type of cells accepted . . . . 7
1.9.4 Mechanical dimensions (mm ) . . . . . (in) 7
1.9.5 Gross weight, net and tare . . . . . . . . . 7
1.10 Included funcons. . . . . . . . . . . . . . . 8
1.11 ‘Tare’ funcons included . . . . . . . . . . . 8
1.12 Examples of connecons for more than 1 cell 9
1.12.1 Connecons with a juncon box . . . . . 9
1.12.2 Connecons with 3 or 4 load cells . . . . 9
1.13 Conguraon . . . . . . . . . . . . . . . . .10
1.13.1 How to operate the menus . . . . . . . .10
1.13.2 Inial set-up . . . . . . . . . . . . . . . .11
1.13.3 Inial setup menu . . . . . . . . . . . . .12
1.13.4 Funcon ‘auto-tare’ . . . . . . . . . . . .13
1.13.5 Scale factor . . . . . . . . . . . . . . . . .13
1.13.6 Funcon ‘stock’. . . . . . . . . . . . . . .13
1.2 Index
1.13.7 Advanced conguraon menu . . . . . .14
1.13.8 Alarms. . . . . . . . . . . . . . . . . . . .15
1.13.9 Alarm conguraon . . . . . . . . . . . .16
1.13.10 Display lters . . . . . . . . . . . . . . .17
1.13.11 Rear controls . . . . . . . . . . . . . . .18
1.13.12 Front key ‘LE’ ( ). . . . . . . . . . . . .
318
1.13.13 Fast access. . . . . . . . . . . . . . . . .19
1.13.14 ‘On power up’ funcon. . . . . . . . . .19
1.13.15 ‘Fast access’ conguraon menu . . . .20
1.13.16 ‘On power up’ conguraon. . . . . . .20
1.13.17 Tools . . . . . . . . . . . . . . . . . . . .21
1.13.18 Access to opons conguraons menu 21
1.14 Full conguraon menu. . . . . . . . . . . .22
1.15 Factory conguraon . . . . . . . . . . . . .25
1.16 Messages and errors . . . . . . . . . . . . .25
1.17 To access the instrument . . . . . . . . . . .26
1.18 Modular architecture . . . . . . . . . . . . .26
1.19 Precauons on installaon . . . . . . . . . .27
1.20 Warranty . . . . . . . . . . . . . . . . . . . .27
1.21 CE declaraon of conformity . . . . . . . . .27
2. Output and control modules . . . . . . . . . . .28
2.1 Module PCE-DPD/R . . . . . . . . . . . . . . .28
2.2 Module PCE-DPD/T . . . . . . . . . . . . . . .28
2.3 Module PCE-DPD/SSR. . . . . . . . . . . . . .29
2.4 Module PCE-DPD/AV . . . . . . . . . . . . . .29
2.5 Module PCE-DPD/MB. . . . . . . . . . . . . .30
2.6 Module PCE-DPD/485 . . . . . . . . . . . . .30
2.7 Module PCE-DPD/232 . . . . . . . . . . . . .31
PCE-DPD F
Model Power
-1+Up to 3 slots for opons available
-1 (85-265 Vac/dc)
 
-2 (11/60 Vdc,
 
24 Vac, 48 Vac)
   
1.3 How to order
Opons
PCE-DPD/R (1 relay SPDT)
PCE-DPD/AV (analog output mA & Vdc)
PCE-DPD/MB (Modbus RTU)
PCE-DPD/485 (RS-485)
PCE-DPD/233 (RS-232)
PCE-DPD/T (1 transistor)
PCE-DPD/SSR (1 SSR control)
Product Specifications
| Brand: | PCE Instruments |
| Category: | Measuring equipment |
| Model: | PCE-DPD-F2 |
Do you need help?
If you need help with PCE Instruments PCE-DPD-F2, ask a question below and other users will answer you
Measuring equipment PCE Instruments User Manuals
24 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
22 October 2024
Measuring equipment User Manuals
- Measuring equipment EBERLE
- Measuring equipment Hazet
- Measuring equipment Fluke
- Measuring equipment Megger
- Measuring equipment Kogan
- Measuring equipment AkYtec
- Measuring equipment Voltcraft
- Measuring equipment Klein Tools
- Measuring equipment PeakTech
- Measuring equipment Clean Air Optima
- Measuring equipment Flex
- Measuring equipment CSL
- Measuring equipment Elgato
- Measuring equipment Kern
- Measuring equipment Be Cool
- Measuring equipment ORNO
- Measuring equipment Einhell
- Measuring equipment Mitsubishi
- Measuring equipment Noyafa
- Measuring equipment Megasat
- Measuring equipment Reely
- Measuring equipment Joy-it
- Measuring equipment Logilink
- Measuring equipment Basetech
- Measuring equipment Gossen Metrawatt
- Measuring equipment TFA
- Measuring equipment Owon
- Measuring equipment Extech
- Measuring equipment Milesight
- Measuring equipment Sonel
- Measuring equipment Flir
- Measuring equipment Testo
- Measuring equipment MSW
- Measuring equipment Stamos
- Measuring equipment Ideal
- Measuring equipment Hikmicro
- Measuring equipment Siglent
- Measuring equipment Kopp
- Measuring equipment PICO
- Measuring equipment Enda
- Measuring equipment Wachendorff
- Measuring equipment Ermenrich
- Measuring equipment Beha-Amprobe
- Measuring equipment Adwa
- Measuring equipment Tempo
- Measuring equipment Vemer
- Measuring equipment Testboy
- Measuring equipment Duro Pro
- Measuring equipment Kyoritsu
- Measuring equipment Benning
- Measuring equipment MASIMO
- Measuring equipment Stahlwille
- Measuring equipment SHX
Latest Measuring equipment User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024