Lancom CS-8132F Manual
Read below 📖 the manual in Italian for Lancom CS-8132F (1 pages) in the Switch category. This guide has been helpful for 5 people and has been rated 4.5 stars on average by 2 users
Page 1/1
Hardware Quick Reference
i
Before initial startup, please make sure to take notice of the information regarding
the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby
power socket that is freely accessible at all times.
All power plugs of the device must be freely accessible.
Please note that support for third-party accessories is not provided.
Mounting & connecting
LED description & technical details
Use an Ethernet cable to use this out-of-band service port
for an IP interface independent of the switching plane for
management tasks or connection to a monitoring server.
In particular, this port can be used as a VPC-keepalive link
(split-brain detection).
Connect a USB stick to the USB interface to store general
configuration scripts or debug data. You can also use this
interface to upload a new firmware.
Connect the configuration interface to the USB interface of
the device you want to use for configuring / monitoring the
switch using the serial configuration cable supplied.
10G SFP+ in-band management interface
(for future use)
Insert suitable LANCOM transceiver modules into the QSFP28 interfaces 1 to 32.
Choose cables which are compatible with the transceiver modules and connect them as
described in the transceiver modules mounting instructions:
lancom-systems.com/transceiver-modules-mi.
Use the enclosed grounding bracket with screw to secure the switch against ground.
To remove a fan module in case of defect, loosen the knurled screw of the module and
remove the module from the plug-in unit. To install a new fan module, push it into the
corresponding slot. Fasten the module to the switch housing with the knurled screw.
Please note that a defective fan should be replaced within 48h.
Supply the device with power via the power supply sockets of the power supply
modules. Use the supplied power cords or a country-specific LANCOM Power Cord.
To remove the power supply module, disconnect the module from the power supply and
then pull the plug out of the module. While pressing the release lever to the left, you
can pull the module out of the device by the handle .
FAN
2
FAN
1
FAN
0
CS-8132F
SYS
FAN
PSO
PS1
ID
MGMT
RESET SS
31 3229 3027 2825 2623 2421 2219 2017 1815 1613 1411 129 107 85 63 41 2
Left LED
Right LED
LANCOM CS-8132F
CS-8132F
SYS
FAN
PSO
PS1
ID
MGMT
RESE T
SS
15 1613 1411 129 107 85 63 41 2
FAN
0
Product Specifications
| Brand: | Lancom |
| Category: | Switch |
| Model: | CS-8132F |
Do you need help?
If you need help with Lancom CS-8132F, ask a question below and other users will answer you
Switch Lancom User Manuals
14 October 2024
14 October 2024
14 October 2024
14 October 2024
14 October 2024
13 October 2024
13 October 2024
Switch User Manuals
- Switch Bosch
- Switch IKEA
- Switch Huawei
- Switch HP
- Switch EBERLE
- Switch TP Link
- Switch Totolink
- Switch D-Link
- Switch StarTech.com
- Switch Cudy
- Switch Extron
- Switch Lindy
- Switch Ecler
- Switch Digitus
- Switch LevelOne
- Switch Engenius
- Switch CyberPower
- Switch CSL
- Switch Smart-AVI
- Switch Generac
- Switch Dahua Technology
- Switch Cambium Networks
- Switch ORNO
- Switch Planet
- Switch PCE
- Switch Equip
- Switch Mikrotik
- Switch Speaka
- Switch Alcatel
- Switch Elation
- Switch Logilink
- Switch Advantech
- Switch Atlona
- Switch Robbe
- Switch Crestron
- Switch IPGARD
- Switch PureLink
- Switch Blustream
- Switch WHALE
- Switch Tenda
- Switch Suevia
- Switch ZyXEL
- Switch Homematic IP
- Switch Setti+
- Switch Trendnet
- Switch Intellinet
- Switch Kaiser
- Switch QNAP
- Switch Rex
- Switch Juniper
Latest Switch User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024
26 October 2024