Philips DDNP1501 Manual

Philips Not categorized DDNP1501

Read below 📖 the manual in Italian for Philips DDNP1501 (2 pages) in the Not categorized category. This guide has been helpful for 2 people and has been rated 4.5 stars on average by 2 users

Download PDF

Page 1/2

DDNP1501

105 mm (4.1 in)

95 mm (3.8 in)

75 mm (2.9 in)

59 mm (2.3 in)

45 mm

(2 in)

45 mm

(2 in)

www.lighting.philips.com/dynalite

Network Power

Supply

Installation Instructions

Instructions d’installation

Installationsanweisungen

Instrucciones de instalación

Istruzioni per l’installazione

Installatie-instructies

インストール手順

安装指示

40° C (104° F)

0° C (32° F)

≤

95%

IEC Pollution Degree II

Devices must be installed in an

approved enclosure by a qualied

electrician in accordance with all

national and local electrical and

construction codes and regulations.

Les appareils doivent être installés dans un lieu jugé

apte, par un électricien qualié et conformément

aux règles et normes locales et nationales en

matière d’électricité et de construction.

Die Geräte müssen von einem geprüften Elektriker

entsprechend allen nationalen und lokalen Elektro

– und Bauvorschriften in einem zugelassenen

Gehäuse installiert werden.

Los dispositivos se deben instalar en un recinto

aprobado por un electricista cualicado de

acuerdo a todos los reglamentos eléctricos y de

construcción locales y nacionales pertinentes

I dispositivi devono essere installati da un

elettricista qualicato in un luogo approvato, in

conformità a tutti gli standard e le norme nazionali

e locali vigenti in materia di impianti elettrici e

costruzioni edilizie.

Apparaten moeten door een erkende elektricien

worden geïnstalleerd in een goedgekeurde

behuizing in overeenstemming met alle nationale

en lokale elektriciteits – en bouwvoorschriften

en wetgeving.

デバイスを取り付ける際は、資格のある電気技師に依頼

し、電気と建設に関する国および地域のすべての法令に

従って、認可されている筐体内に取り付けてください。

根据国家/地区及当地的电气与建筑规范和法规，该设

备必须由有资质的电工安装在经批准的外罩内。

DyNet RS-485

SHLD

D +

GND

D -

+12 V

N L

Shld Gnd

D + D -

+12 V

SHLD

D +

GND

D -

+12 V

DyNet RS-485

≤ 2 A

2 A

5 6

2 B

N L

≤ 2.5 mm2

13+ AWG

15 V

1 A (@ 120 V )

1.5 A (@ 230 V )

+12 V

D -

GND

D +

SHLD

100-24 V0

0.2 A5

This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

IEC Overvoltage Category III

AZZ 372 0718 R13

change without notice. No representation or warranty as to the accuracy or

completeness of the information included herein is given and any liability

for any action in reliance thereon is disclaimed. Philips and the Philips

Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other

trademarks are owned by Signify Holding or their respective owners.

www.lighting.philips.com/dynalite