Perlick 3076 Manual

Read below 📖 the manual in Italian for Perlick 3076 (6 pages) in the Not categorized category. This guide has been helpful for 4 people and has been rated 4.5 stars on average by 2 users

Page 1/6
Installation Instructions
Air-Cooled Wall Mount Beverage Dispenser
Form No. Z2507
Rev. 11.30.2022
Air Cooled Wall Mount Dispenser Installation Instructions
2
Installation of Air cooled Wall Mount Dispenser
1. Remove screws which
secure the back plate
to the dispenser.
3. Remove screws which
secure the bottom plate to
the dispenser.
Remove bottom plate and
set aside.
Parts Bag Included with Tower:
2. Remove back
plate and set aside.
Preparing for Installation:
Black Poly-tape Clear poly-tape
Elbow drain
tting with
barbed tailpiece
Straight drain
tting with
barbed tailpiece Spanner wrench
Parts bag contents include –
Included with Tower:
Wall Mount Dispenser
(Faucets and tap handles
shown are not included)
Mounting Bracket
Other Parts Needed for Installation: The parts required will vary depending on the installation.
PART NO. DESCRIPTION
C26609 Wall Mounted Air Shaft Connector, Cooler (1 required)
1655R Blower Kit, 134 CFM
C15365-1 3” Hose duct, blower to air shaft inside cooler - 12.5 feet
C15365-2 3” Hose duct, blower to air shaft inside cooler - 25 feet
C15366-1 Coupling Sleeve for 3” air shaft tube (1 required when joining two 12” sections)
C31573 Poly housing hanger strap kit
61082-1 Aluminum housing hanger
1390D 1/2” I.D. Vinyl Drain Tube – Anti-Microbial
Air Cooled Wall Mount Dispenser Installation Instructions
Form No. Z2507
Rev. 11.30.2022
3. Determine mounting location for dispensing
unit on wall.
Secure bracket to the wall.
Note: Align screws with as many wall studs
as possible to provide adequate support for
the dispenser.
After installing one screw, check to insure the
bracket is perfectly level before installing
remaining screws.
Note: Use mounting screws and anchors if
needed which are appropriate for the wall the
dispenser is to be installed on.
4. Hang back plate on the installed hanging track
making sure the plate is centered on the track.
Trace holes onto wall.
Remove back plate and set aside.
5. Measure to locate the exact center of each hole
location.
Mark centers.
6. Cut holes for air tube and beverage leads with
a 3-1/2” to 4” hole saw. The hole is larger than the
diameter of the air inlets on the dispensing units
to provide clearance when lowering the dispenser
into position.

Product Specifications

Brand: Perlick
Category: Not categorized
Model: 3076

Do you need help?

If you need help with Perlick 3076, ask a question below and other users will answer you




Not categorized Perlick User Manuals

Perlick

Perlick PKD24A Manual

13 October 2024
Perlick

Perlick PKC24 Manual

13 October 2024
Perlick

Perlick PKBR24 Manual

13 October 2024
Perlick

Perlick PKD24B Manual

13 October 2024
Perlick

Perlick PKHT24 Manual

13 October 2024
Perlick

Perlick HP24TO-4 Manual

13 October 2024
Perlick

Perlick HC24FS-4 Manual

13 October 2024
Perlick

Perlick HC24FS Manual

13 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals