CRUX RVCCH-75WM Manual

CRUX Not categorized RVCCH-75WM

Read below 📖 the manual in Italian for CRUX RVCCH-75WM (3 pages) in the Not categorized category. This guide has been helpful for 4 people and has been rated 4.5 stars on average by 2 users

Page 1/3
- Interface includes Audio / Video Input to connect an extra A/V source.
- OEM style Spare Tire mount reverse camera included.
- Camera has moving parking guide lines to show path direcon while backing up.
- Acvates MYGIG Screen for enabling Video features.
- Supports vehicles with manual transmission. See note below.
- Plug and Play connecons for ease of use.
NOTE: Does not supply +12V Reverse Trigger on vehicles with manual transmission.
Camera power must be tapped from the +12V reverse light wire instead.
-75WM MODULE CH
-75WM HARNESS CH
CCH-01M SPARE TIRE MOUNT CAMERA with MOVING LINES
Rev.0926 17
1 / 3
INSTALLING THE CAMERA AND INTERFACE
1. Remove the outside mounted spare re.
2. Mount the metal bracket onto the spare re bolts and secure with the star washers. camera’s
3. Route the cable towards the radio and make the power and video connecons.
4. Remove the factory radio to gain access to the factory connectors.
5. Plug in the T-harness with WHITE and GRAY connectors. (See Wiring Diagram above)
6. Connect the 8-pin Molex connector from the T-harness with GRAY connectors to the CAN Interface.
7. Use the WHITE 12V Reverse Output wire to power the camera (see Wiring Diagram above). DO NOT
connect the red power wire, near the camera, insulate this red wire to avoid to the reverse light and
from shorng. the vehicle has a manual transmission, the camera power must be tapped to the If
+12V reverse light wire instead. In this case the WHITE 12V Reverse Output wire is not used and
should be insulated to avoid from shorng.
8. Plug in the YELLOW MALE RCA from the camera cable to the YELLOW FEMALE RCA of the T-Harness
with WHITE connectors.
9. Connect GREEN wire to +12V for a non permanent Video in Moon feature.
10. Set the proper DIP Switch sengs on the CAN Interface. (See Chart above)
11. Cut the thin white wire on the camera cable to enable the parking guide lines.
12. Test the camera before re-installing the radio.
Rev.0926 17
2 / 3
Please note that the WHITE 12V
Reverse Output wire does not
supply power on vehicles with
manual transmission and should
be insulated to avoid from
shorng. Connect the camera
power to the OE reverse light
+12V wire instead.
DIP SWITCH SETTING
OFF
VIM Disable
ON
Rear-View Camera Enable
OFF
N/A
OFF
Opon for GREEN Wire
OFF
CAN Terminaon Radio Side
ON
CAN Terminaon Car Side
The parking lines are there to assist you while reversing. To acvate the parking lines simply cut/disconnect the
WHITE loop wire located near the 4 pin camera connector.
What the Lines mean:
Green Line: CLEAR
Yellow Line: GETTING CLOSE
Red Line: WARNING - VERY CLOSE
White Line: SHOWS THE PATH DIRECTION
VES will be your source for the AV Input.
To access the VES buon, press the RADIO/MEDIA buon on the le side of the radio. The VES buon is only
acve aer the interface is properly installed.
JEEP
2007 2017 WRANGLER –
MyGig Radio
Rev.0926 17
3 / 3

Product Specifications

Brand: CRUX
Category: Not categorized
Model: RVCCH-75WM

Do you need help?

If you need help with CRUX RVCCH-75WM, ask a question below and other users will answer you




Not categorized CRUX User Manuals

CRUX

CRUX SWRFD-60T Manual

19 October 2024
CRUX

CRUX SWRFD-60B Manual

13 October 2024
CRUX

CRUX SOOGM-16K Manual

13 October 2024
CRUX

CRUX SOCGM-17B Manual

13 October 2024
CRUX

CRUX DKGM-49 Manual

13 October 2024
CRUX

CRUX DKGM-C2S Manual

13 October 2024
CRUX

CRUX DKVW-21 Manual

13 October 2024
CRUX

CRUX SOHTL-20 Manual

13 October 2024
CRUX

CRUX AVIGM-04S Manual

13 October 2024
CRUX

CRUX SOCVW-21 Manual

13 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals