CRUX DKGM-48D Manual

Read below 📖 the manual in Italian for CRUX DKGM-48D (4 pages) in the Not categorized category. This guide has been helpful for 5 people and has been rated 4.5 stars on average by 2 users

Page 1/4
- Retains factory features in select GM Class II Data Bus vehicles while functioning with an
aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Voice Recognition Command from factory SWC.
- Supports Bose, Y-91 and non-amplified audio systems.
- Retains chime functions.
- Built-in chime volume adjustment.
- Double DIN Dash Kit included.
- EIA color coded wiring for easy installation.
GM- D Module 48
GM- D Harness (GM-C2) 48
SWC Cables
Double DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime includes: seat belt, check engine, key in ignition, low fuel, low oil and lights on.
rev.092821
1/4
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below. See page 4 for SWC
button functions.
3.5MM SWC CABLE
The SWRGM- D Module allows for both types of connections: 48
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
is used for BOSS, DUAL, FAHRENHEIT, JENSEN, PIONEER, POWER ACOUSTIK, SONY & OPTION B
SOUND STREAM units.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the DKGM- D has a built-in Bose adaptor that allows the proper audio 48
input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin connector on
the harness to the GRAY female 8-pin connector on the GM- D 48 module. The module is also labeled Bose” and
“Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM- D module. 48
2/4
BOSE
Connection
Non-BOSE
Connection
rev.092821
The - D has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the DKGM 48
volume, simply use a suitable screwdriver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Dash Kit Assembly
Please make sure that you have all the parts shown below.
(1) Main trim ring
(1) Left ISO mounting bracket
(1) Right ISO mounting bracket
3/4
rev.092821

Product Specifications

Brand: CRUX
Category: Not categorized
Model: DKGM-48D

Do you need help?

If you need help with CRUX DKGM-48D, ask a question below and other users will answer you




Not categorized CRUX User Manuals

CRUX

CRUX SWRFD-60T Manual

19 October 2024
CRUX

CRUX SWRFD-60B Manual

13 October 2024
CRUX

CRUX SOOGM-16K Manual

13 October 2024
CRUX

CRUX SOCGM-17B Manual

13 October 2024
CRUX

CRUX DKGM-49 Manual

13 October 2024
CRUX

CRUX DKGM-C2S Manual

13 October 2024
CRUX

CRUX DKVW-21 Manual

13 October 2024
CRUX

CRUX SOHTL-20 Manual

13 October 2024
CRUX

CRUX AVIGM-04S Manual

13 October 2024
CRUX

CRUX SOCVW-21 Manual

13 October 2024

Not categorized User Manuals

Latest Not categorized User Manuals