Honeywell C7189R Manual

Read below 📖 the manual in Italian for Honeywell C7189R (20 pages) in the Thermostat category. This guide has been helpful for 6 people and has been rated 4.5 stars on average by 2 users

Page 1/20
Installation
Guide
C7189R
Wireless Indoor Sensor
Capteur d’intérieur sans fil
Sensor inalámbrico para interiores
69-2459EFS-05
Installation Guide
ii
69-2459EFS05
® U.S. Registered Trademark.
Copyright © 2012 Honeywell International Inc.
All rights reserved.
About your wireless indoor sensor
This sensor monitors temperature and humidity in any indoor location and transmits it
wirelessly to the thermostat.
You can set the system to monitor temperature at the thermostat, or at the sensor location,
or use an average of both to optimize comfort throughout the home. The thermostat can
use up to 6 wireless indoor sensors.
When multiple sensors are installed, the thermostat can monitor temperature and humidity
in separate locations. For example, one sensor can control humidication on the main level,
while another controls dehumidication in a crawl space. For more information, see the
instructions provided with the thermostat.
Note: The wireless indoor sensor is compatible only with RedLINK 2.0 thermostats.
Operating Ambient Temperature: 0 to 120° F (-17.8 to 48.9° C)
For Optimal Battery Life: 35 to 11F (1.7 to 45.6° C)
Operating Relative Humidity: 5% to 90% (non-condensing)
Physical Dimensions: 2-7/8 x 1-7/8 x 15/16 inches (74 x 48 x 24 mm)
The thermostat will display a warning to replace batteries in the indoor sensor about 2 months
before power is depleted. The sensor status light will begin flashing red about 2–3 weeks before
power is depleted. During normal operation, the status light remains off.
Wireless Indoor Sensor
169-2459EFS05
MCR32933
MCR32934 MCR32935
Install 2 fresh AAA alkaline batteries.
Status light will briefly flash green. If it
flashes red, batteries are not good.
Install batteries and link sensor to thermostat
1
Install batteries, then enter Wireless Setup mode at the thermostat. Press and
release the CONNECT button to link the wireless sensor to the thermostat.
Press and release CONNECT.
After a short delay, the status light
will glow green for 15 seconds.
If the status light is red, the
sensor did not link with the
thermostat. See Note.
Verify the thermostat is in the Wireless Setup
mode and the indoor sensor is at least 2 feet
away from the EIM or thermostat.

Product Specifications

Brand: Honeywell
Category: Thermostat
Model: C7189R

Do you need help?

If you need help with Honeywell C7189R, ask a question below and other users will answer you




Thermostat Honeywell User Manuals

Thermostat User Manuals

Latest Thermostat User Manuals

Heatmiser

Heatmiser PRT-ETS Manual

25 October 2024
Heatmiser

Heatmiser PRT-W Manual

25 October 2024
Heatmiser

Heatmiser PRTHW Manual

25 October 2024
Heatmiser

Heatmiser PRT-EWTS Manual

25 October 2024
Heatmiser

Heatmiser DT-N Manual

25 October 2024
Heatmiser

Heatmiser DT-EW Manual

25 October 2024
Heatmiser

Heatmiser PRTHW-WTS Manual

25 October 2024
Heatmiser

Heatmiser PRT-RPTS Manual

25 October 2024
Heatmiser

Heatmiser PRT-RP Manual

25 October 2024
Heatmiser

Heatmiser PRT-B Manual

25 October 2024