Bosch HomeProfessional WTY88701AU Manual
Bosch
Tumble dryer
HomeProfessional WTY88701AU
Read below π the manual in Italian for Bosch HomeProfessional WTY88701AU (6 pages) in the Tumble dryer category. This guide has been helpful for 5 people and has been rated 4.5 stars on average by 2 users
Page 1/6
1
Environmentally-responsible disposal
β Dispose of packaging in an environmentally-responsible manner.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling of used appliances as
applicable throughout the EU.
Installation
β Scope of delivery: dryer, instruction manual, installation and maintenance instructions,
jug and woollens basket (depending on the model).
β Check dryer for transport damage.
β The dryer is very heavy. Do not attempt to lift it on your own.
β Be careful to avoid sharp edges.
β Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
β If in doubt, have the appliance connected by a specialist.
Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
β Ensure that the appliance is installed on a clean,
level and firm surface.
β The appliance plug must always be accessible.
β Do not obstruct the air inlet on the dryer.
β Keep the area around the dryer clean.
β Level the dryer using the threaded feet
and a spirit level.
β Do not remove the threaded feet under any
circumstances.
For mains connection, see Safety instructions page 13.a
β Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
β The mains voltage and the voltage shown on the rating plate (apage 4) must be the same.
The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container .aPage 4
2. Select any programme using the programme selector.
3. Press the ( /Pause) button condensation water is pumped into the container.$ξξ Start a
4. Wait 5 minutes and then empty the condensation container again.
5. Switch the dryer off using the programme selector.
6. Transport the dryer in a vertical upright position.
7. Following transportation, do not use the dryer for two hours.
The dryer contains residual water.
This can flow out if the dryer is tilted.
The refresher tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
1.
Make sure that the air
inlet remains unobstructed
Clean and level
D
o no
t
se
t
up
th
e
d
ryer
b
e
hi
n
d
a
d
oor or s
lidi
ng
door, as this may obstruct the dryer door or prevent
it from opening. This will prevent children from
locking themselves in, thereby putting their lives at
risk.
Take all accessory parts out of the drum.
The drum must be empty.
2.
2
Care and cleaning
Dryer housing, control panel
Remove detergent residues immediately.
Wipe with a soft, damp cloth.
Do not clean with a water jet.
During drying, water may accumulate between the window and the seal.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure how damp the laundry is.
A thin layer of limescale may build up on the moisture sensors after
prolonged use.
This must be removed regularly.
1. Open the door and clean the moisture sensors with a damp
sponge that has a rough surface.
Do not use steel wool or abrasive materials.
Cover for steam nozzle in the drum (depending on the model)
After prolonged operation, limescale and fluff may accumulate on the cover of the steam
nozzle. Clean regularly:
1. Open the door and remove the cover with a screwdriver.
Clean the cover under running water.
2. Push and click the cover back in place.
Clean the filter in the refresher tank if it is dirty (depending on the model)
Regularly clean the filter under running water a This prevents stubborn deposits/dirt from
building up.
1. Remove the condensation container.
2. Remove the filter and clean it under running water.
3. Re-insert the filter and push in the condensation container until it
locks into place.
3
Care and cleaning
Heat exchanger
The dryer's heat exchanger is automatically cleaned during drying and Heat exchanger is
being rinsed is displayed in the display panel. Do not pull out the condensation container
during this cleaning process.
Filter in the condensation container
The filter is cleaned automatically when the condensation container is emptied.
However, the filter should still be cleaned regularly under running water This prevents a
stubborn deposits/dirt from building up.
If the condensation drain is installed (depending on the model), it is not necessary to clean
the filter separate .aInstructions for the condensation drain
1. Pull out the condensation container.
2. Pull the filter out of its snap-in lock.
3. Clean the filter under running water or in the dishwasher.
4. Refit the filter.
5. Push the condensation container back in until it locks into place.
Only operate the dryer with the filter inserted.
4
After-sales service
If you cannot rectify the fault yourself instruction manual: aWhat to do if...
page 12, please contact our after-sales service. We will always find an appropriate solution
and avoid unnecessary visits by engineers.
You can find the contact details for your nearest after-sales service on page 12 of the
instruction manual or in the after-sales service directory.
Please give the after-sales service the product number (E no.) and the production number
(FD) of the appliance.
Product number Production number
You can find this information:
inside the door* / in the opened service flap*
and on the rear of the appliance.
*depending on the model
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest
assured that the repair will be carried out by trained service technicians using original spare
parts.
Optional accessories (order from the after-sales service using the order number, depending on model)
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer must be fastened to the washing machine using this connection set.
WTZ 11400: with pull-out worktop.
Wollens basket
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for
βWoollens basketβ).
Platform
For easier loading and unloading. The basket contained in the drawer can be used
to carry the laundry.
Technical data
Dimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)
Weight approx. 57 kg
Max. capacity* 8 kg / 9 kg
Condensation container 4.6 l
Refresher tank approx. 0.4 l
Connection voltage 220-240 V
Connected load max. 1000 W (for models with a max. 1600 W steam
function)
Fuse protection 10 A
Ambient temperature 5 - 35 Β°C
Product number
Production number Inside of door
The rating plate can be found on the back of the dryer.
*depending on the model operating instructions: Programme overview, page 7aξ
WTZ
20410
WMZ
20600
WMZ
20500
5
Reversing the door
1 6
22.
1.
7
3 8
4 9
53.
1.
2.
10
6 11
9406 / 9000695672
*695672*
6
Reversing the door
11 16
12 17
13 18 1.
3.
2.
14 19
15 20 1.
2.
16 21
7
Reversing the door
21 26
22
1.
2.
27
23
1.
2.
3.
28
24
1.
2.
29
25 1. 2.
26
Dryer
Contents Page
ΚEnvironmentally-friendly disposal . . . . . . 1
ΚInstallation . . . . . . . . . . . . . . . . . . . . . . . . 1
ΚFrost protection / Transport. . . . . . . . . . . 1
ΚCare and cleaning . . . . . . . . . . . . . . . 2/3
ΚAfter-sales service . . . . . . . . . . . . . . . . . . 4
ΚOptional accessories . . . . . . . . . . . . . . . . 4
ΚTechnical data . . . . . . . . . . . . . . . . . . . . 4
ΚReversing the door . . . . . . . . . . . . . . . 5/7
Installation and
maintenance
instructions
Read these instructions before operating the dryer.
You must also observe the separate instruction manual.
Keep all the documents in a safe place for future reference, or to
pass on to the next owner.
en
1
Environmentally-responsible disposal
β Dispose of packaging in an environmentally-responsible manner.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling of used appliances as
applicable throughout the EU.
Installation
β Scope of delivery: dryer, instruction manual, installation and maintenance instructions,
jug and woollens basket (depending on the model).
β Check dryer for transport damage.
β The dryer is very heavy. Do not attempt to lift it on your own.
β Be careful to avoid sharp edges.
β Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
β If in doubt, have the appliance connected by a specialist.
Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
Setting up the dryer
β Ensure that the appliance is installed on a clean,
level and firm surface.
β The appliance plug must always be accessible.
β Do not obstruct the air inlet on the dryer.
β Keep the area around the dryer clean.
β Level the dryer using the threaded feet
and a spirit level.
β Do not remove the threaded feet under any
circumstances.
For mains connection, see Safety instructions page 13.a
β Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
β The mains voltage and the voltage shown on the rating plate (apage 4) must be the same.
The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container .aPage 4
2. Select any programme using the programme selector.
3. Press the ( /Pause) button condensation water is pumped into the container.$ξξ Start a
4. Wait 5 minutes and then empty the condensation container again.
5. Switch the dryer off using the programme selector.
6. Transport the dryer in a vertical upright position.
7. Following transportation, do not use the dryer for two hours.
The dryer contains residual water.
This can flow out if the dryer is tilted.
The refresher tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.
1.
Make sure that the air
inlet remains unobstructed
Clean and level
D
o no
t
se
t
up
th
e
d
ryer
b
e
hi
n
d
a
d
oor or s
lidi
ng
door, as this may obstruct the dryer door or prevent
it from opening. This will prevent children from
locking themselves in, thereby putting their lives at
risk.
Take all accessory parts out of the drum.
The drum must be empty.
2.
2
Care and cleaning
Dryer housing, control panel
Remove detergent residues immediately.
Wipe with a soft, damp cloth.
Do not clean with a water jet.
During drying, water may accumulate between the window and the seal.
Moisture sensor
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure how damp the laundry is.
A thin layer of limescale may build up on the moisture sensors after
prolonged use.
This must be removed regularly.
1. Open the door and clean the moisture sensors with a damp
sponge that has a rough surface.
Do not use steel wool or abrasive materials.
Cover for steam nozzle in the drum (depending on the model)
After prolonged operation, limescale and fluff may accumulate on the cover of the steam
nozzle. Clean regularly:
1. Open the door and remove the cover with a screwdriver.
Clean the cover under running water.
2. Push and click the cover back in place.
Clean the filter in the refresher tank if it is dirty (depending on the model)
Regularly clean the filter under running water This prevents stubborn deposits/dirt from a
building up.
1. Remove the condensation container.
2. Remove the filter and clean it under running water.
3. Re-insert the filter and push in the condensation container until it
locks into place.
Product Specifications
| Brand: | Bosch |
| Category: | Tumble dryer |
| Model: | HomeProfessional WTY88701AU |
Do you need help?
If you need help with Bosch HomeProfessional WTY88701AU, ask a question below and other users will answer you
Tumble dryer Bosch User Manuals
27 October 2024
26 October 2024
26 October 2024
21 October 2024
21 October 2024
18 October 2024
15 October 2024
14 October 2024
14 October 2024
14 October 2024
Tumble dryer User Manuals
- Tumble dryer Candy
- Tumble dryer Electrolux
- Tumble dryer Samsung
- Tumble dryer LG
- Tumble dryer AEG
- Tumble dryer Panasonic
- Tumble dryer AEG Electrolux
- Tumble dryer BEKO
- Tumble dryer Teka
- Tumble dryer Miele
- Tumble dryer Siemens
- Tumble dryer Arcelik
- Tumble dryer Smeg
- Tumble dryer Hisense
- Tumble dryer Hoover
- Tumble dryer Hotpoint
- Tumble dryer Whirlpool
- Tumble dryer Nabo
- Tumble dryer Artusi
- Tumble dryer Kogan
- Tumble dryer Midea
- Tumble dryer Sauber
- Tumble dryer Gram
- Tumble dryer Gemini
- Tumble dryer Haier
- Tumble dryer Vox
- Tumble dryer Grundig
- Tumble dryer Stirling
- Tumble dryer Exquisit
- Tumble dryer Maytag
- Tumble dryer Defy
- Tumble dryer GE
- Tumble dryer Mybeo
- Tumble dryer Hyundai
- Tumble dryer Infiniton
- Tumble dryer Ufesa
- Tumble dryer Indesit
- Tumble dryer Blaupunkt
- Tumble dryer Adler
- Tumble dryer AYA
- Tumble dryer Sharp
- Tumble dryer Eldom
- Tumble dryer Fisher And Paykel
- Tumble dryer Elba
- Tumble dryer Philco
- Tumble dryer Wisberg
- Tumble dryer Tesla
- Tumble dryer Becken
- Tumble dryer Element
- Tumble dryer Heinner
- Tumble dryer Gaggenau
- Tumble dryer Hiberg
- Tumble dryer Zerowatt
- Tumble dryer Otsein-Hoover
- Tumble dryer Baumatic
- Tumble dryer Iberna
- Tumble dryer KDK
- Tumble dryer Esatto
- Tumble dryer Electra
- Tumble dryer Rex
- Tumble dryer Castor
- Tumble dryer Classique
- Tumble dryer Essentiel B
Latest Tumble dryer User Manuals
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024
27 October 2024